无齿轮曳引机装配线专业定制 全自动曳引机生产线结构合理
曳引机工作时，机房内空气的温度保持在5摄氏度到40摄氏度之间且海拔高度不得超越1000米，因为机房内的空气温度保持在5摄氏度到40摄氏度之间，环境中的空气不含有腐蚀性的气体，易燃性的气体供电电压动摇于额定值误差不超越百分之正负七，工作频率动摇与额定值误差不超越百分之正负一。
曳引机的外表应坚持每天清洗，防止污垢，定时用洁净的棉丝擦洗曳引机的制动轮与曳引轮的工作面，定时检查制动器的工作状况，在有需要时，应及时调整及替换，注意电磁圈身为不超越90k，定时检查也因困的磨损状况。
电梯曳引机是电梯的动力设备，又称电梯主机。功能是输送与传递动力使电梯运行。它由电动机、制动器、联轴器、减速箱、曳引轮、机架和导向轮及附属盘车手轮等组成。导向轮一般装在机架或机架下的承重梁上。盘车手轮有的固定在电机轴上，也有平时挂在附近墙上，使用时再套在电机轴上。
曳引机总装、测试生产线适用于曳引机、电梯主机产品，可完成曳引机装配、总装、输送、搬运、检测、包装等生产工艺。生产线引用国际先进技术，自动化程度高，结构合理、坚固耐用、外观精美。可以减少操作工人、降低工人工作强度，从而降低公司的运营成本和生产成本。提高生产效率和产品质量，同时还会提高良好的企业形象。
曳引机故障分析及排除方法
1、现象：牵引机制动刹车时有明显的冲击感，那顿代顿。
原因：①制动蹄和制动轮间隙过大，国际规定小于0.7mm。 ②蜗杆轴轴向间隙过大。 ③蜗轮啮合齿隙太大，这种情况很容易发生在牵引机上已经使用了多年。
排除方法：①将清关调整为标准要求。 ②检查蜗轮推力轴承的锁紧螺母是否松动，如果没有松动应该减薄垫片，使得间隙符合工厂标准要求。 ③蜗轮中心距离多种方式如：支架，斜坡和偏心，但可使后隙调整到出厂要求。
2、现象：机噪声，室内噪音超过80db（a）。
原因：①电机绕组失效，导致高频交流声，发生在低速绕线操作，有时也会发生高速运转，是电机制造的难题。 ②蜗轮接触点的位置偏向螺钉或蜗轮表面较差（容易发生在铲齿表面）。 ③轴轴推力轴承滚道质量差。 ④蜗杆滑动轴承和推力轴承油块，使轴承润滑差。 ⑤推力轴承定位端与蜗杆轴垂直方向不同，使轴承滚道偏移。
补救措施：①应由专业人员进行检修。 ②调整蜗轮的接触面积以偏离分离端。如刮铲造成的一般应更换蠕虫。 ③更换合格的轴承。 ④清除油。 ⑤维修或更换轴承座。
产品英文详情介绍
work reasonably hoisting machine, the temperature of the air inside the room is maintained gearless traction machine specialized custom automatic assembly production line structure of the hoisting machine and can not exceed 1,000 meters altitude between 5 degrees celsius to 40 degrees celsius, because the air temperature in the room between 5 degrees celsius to 40 degrees celsius, ambient air does not contain corrosive gases, flammable gas supply voltage does not exceed the error vacillate rated plus or minus seven percent, with nominal operating frequency error does not shake beyond percent plus or minus one. should adhere to the outer hoist cleaned every day, to prevent fouling, the timing of brake face scrub wheel traction sheave and the hoisting machine with a clean cotton yarn, regular inspection of the condition of the brake, if necessary, should be adjusted and replace, pay attention to the electromagnetic coil as no more than 90k, but also because of the storm regularly check the wear. the elevator hoisting machine is powered elevator equipment, also known as elevator hosts. function is to transport and transfer power to make the elevator run. it consists of an electric motor, brakes, couplings, gearbox, traction wheels, guide wheels and the frame subsidiary plate and the hand wheel and other components. guide wheel bearing beam is typically mounted under the rack or rack. some hand wheel disc fixed to the motor shaft, there are usually mounted near the wall, and then sets the motor shaft during use. hoisting machine assembly, test production line is suitable for hoisting machine, the host product elevator, the hoisting machine can be completed assembly, assembly, transport, handling, testing, packaging, and other production processes. production line using international advanced technology, high degree of automation, reasonable structure, strong and durable, attractive appearance. it can reduce operating workers, reduce the work intensity of workers, thereby reducing the company's operating costs and production costs. improve production efficiency and product quality, while also improving good corporate image. traction machine failure analysis and troubleshooting 1, phenomenon: the traction mechanism has a clear sense of shock when moving the brake, that dayton dayton. reasons: 鈶brake shoe and the brake wheel gap is too large, international regulations less than 0.7mm. 鈶worm shaft axial clearance is too large. 鈶worm gear backlash is too large, this situation is likely to occur on the traction machine has been used for many years. exclusion methods: 鈶the clearance is adjusted to the standards. 鈶check the worm gear thrust bearing lock nut is loose, if loose should be no thinning of the gasket, so that the gap in line with factory standards. 鈶a variety of ways such as the worm wheel away from the center: a stent, a ramp and an eccentric, but can be adjusted to clearance requirements of the factory. 2, phenomenon: machine noise, interior noise exceeding 80db (a). reasons: 鈶failure of the motor windings, resulting in a high-frequency hum, the winding operation occurs at low speed, sometimes happen at high speed, the motor is made difficult problem. 鈶position toward the worm wheel contact point or worm screw inferior surface (tooth surface easily occur in the blade). 鈶shaft thrust bearing raceway quality difference. 鈶worm sliding block oil and thrust bearings, the bearing lubrication difference. 鈶thrust bearing end of the worm is positioned in the vertical direction different from the axis, the bearing raceways offset. remedy: 鈶should be professionals overhaul. 鈶to adjust the contact area of 鈥嬧the worm wheel end offset from separating. general should be replaced as a spatula caused by worms. 鈶qualified replacement bearings. 鈶clear oil. 鈶repair or replace the housing.
温岭市创丰自动化设备有限公司
18516036306