【产品介绍】
主要优点：本机由合金刀组成，全部是专业制作刀具的厂家生产。改善竹木粉碎机的缺点、本机带有细度分析设备，可任意控制物料细度。完好的改善通筛率不高的缺点、本机进料口采用自吸式进料，可以防止机器使用过程中被金属块严重损坏。该机机体全部水冷，起到保护作用。 粉碎机中机体内装有定子盘、动子盘、粉碎刀盘。
[introduction] [introduction]
main advantages: the machine is made up of alloy knife, all of which are professional production tool manufacturers. to improve the shortcomings of the machine, wood crusher with fineness analysis equipment, we can control the size of material. good improvement through screening rate is not high, the disadvantages, the machine feeding mouth with self suction feeding, can prevent the machine used by metal block badly damaged. the machine body all water, play a protective role. the machine body is provided with a stator disc grinder, rotor disc, grinding cutter.
木粉机是采用国内外的高科技先进技术最新研制的一种新型超细木粉机，该设备综合了国内外各种传统粉碎机的粉碎原理加以创新，由传统的一种粉碎原理的粉碎机,通过我公司科研人员的大胆设想,并综合国内外多种的粉碎原理成功研制成集三种粉碎原理为一体的高效节能木粉碎机,是专业致力于轻体物料、纤维类物料、脆性物料、韧性物料等特种疑难粉碎的新型制粉设备。该机制作精细，加工工艺高，采用双层机体，机体内注入自来水起到水冷作用，装入了一种新型材料，起到隔音、散热的功能。所以该机在生产使用中噪音小、无振动、扬尘少的特点。
wood powder machine is the domestic and foreign advanced high-tech technology newly developed a new superfine wood flour machine, this equipment combines a variety of domestic and foreign traditional mill to crush the principles of innovation, by a kind of traditional crushing principle of mill, through our research staff boldly conceived, and synthesizes the domestic and foreign various crushing principle successfully developed into a set of three kinds of one of the high efficiency wood crusher crushing principle and is committed to the professional lightweight materials, fiber materials, brittle materials, ductile materials crushing difficult new special milling equipment. the machine is made of fine, high processing technology, the use of double body, the body into the water to play the role of water, into a new type of material, sound insulation, heat dissipation function. therefore, the machine in the production of low noise, no vibration, less dust characteristics.
木粉机结构与粉碎原理：
1,木粉机由粉碎室、塞档室、风室三大部分组成.
2 粉碎刀具有合金刀，刀具全是专业厂家生产。
3 附机由;筛分机、集粉器、除尘器组成。
4 主机粉碎室采用合金刀，由电机带动粉碎机转子高速运转，使机械产生高速气流对粉碎物料产生高强度的撞击力、压缩力、切割力、摩擦力，来达到独特的粉碎功能。
5 合金刀粉碎过程中，转子产生高速度气流随刀片方向旋转，物料在气流中加速并反复冲击、切割摩擦，同时受到三种粉碎作用，由于在受到分析器转子离心力作用时又受到气流向心力的作用，所以当离心力大于向心力时，细粒随气流进入旋风分离器，粗粒子进入离心来复粉碎室继续粉碎直至达到您所满意的细度。
structure and crushing principle of wood flour mill:
1，the wood powder machine is made up of three parts: the crushing chamber, the plug and the file room and the air chamber.
2，crushing knife with alloy knife, cutting tool is the production of professional manufacturers.
3，attached to the machine by; screening machine, dust collector, dust collector.
4，host crushing chamber adopts alloy knife, the motor drives the mill rotor high-speed operation, the machinery to produce high speed airflow of crushing material have high strength of the impact force and compression force, cutting force, friction force, to achieve the unique grinding function.
5，alloy knife crushing process, the rotor flow speed is high with the directions of the blades to rotate, material in flow acceleration and repeated impact, friction cutting and also by three crushing effect, because when subjected to analyzer rotor centrifugal force by the centripetal force of the air, so when the centrifugal force is greater than the centripetal force, fine with the air enter the cyclone separator, coarse particles into centrifugal reflex crushing chamber to smash until it reaches you satisfied with the fineness.
木粉机技术参数
型号 500型木粉机（水冷） 800型木粉机（水冷双室） 900型木粉机（水冷双室）
动力（千克） 11-18.5 22-30 45-55
转速（/分） 3600 3300 2900
道具数量 36 72 96
细度（目） 10-500 10-500 10-500
进料粒度 ＜30-35mm ＜30-40mm ＜40-50mm
物料含水量 ＜6% ＜6% ＜6%
机重（kg） 1600 2600 3800
占地面积（m） 4.6*1.8.3.5 7*2.5*4.3 7*2.8*4.3
河南煊顺机械设备有限公司
18613717026
中国 郑州