ys1 陶瓷电容压力变送器ys1(ys-1)ys1 ceramic capacitance pressuretransmitter概述ys1(ys-1)型陶瓷电容压力变送器采用具有国际先进水平的陶瓷电容压力传感器,配合高精度电子元件,经严格的工艺过程装配而成。它采用无中介液的压力测量技术,充分发挥了传感器的技术优势,使变送器具有优异的性能,同时抗过载和抗冲击能力强、温度漂移小、稳定性高、具有很高的测量精度。ys1(ys-1)型陶瓷电容压力变送器具有多种量程、多种连接形式及多种接液材质。可广泛用于石油、化工、电力、冶金、制药、食品等许多工业领域,可适应各种工业场合及介质,是传统压力表及传统压力变送器的理想升级换代产品,是工业自动化领域理想的压力测量仪表。陶瓷电容压力变送器广泛应用于液体、气体、蒸汽压力测量,液体液位测量。generalremarkys1(ys-1) ceramic capacitance pressure transmitter adopts internationally advanced ceramic capacitance pressure sensor, fitted with high accuracy electronicelements, through strict processassembly. it adopts no medium liquid measuring technology, fully perform transmitter s technical advantage, make transmitter s more excellent function, meanwhile stronger anti overload and antiimpact ability, small thermo drift, high stability, high measuring accuracy.ys1(ys-1) ceramic capacitance pressure transmitter has many range, connection types and wetted materials. widely used inpetroleum, chemical, power,metallurgy, pharmaceutical, food industries etc, suitable for various industrial environments, is ideal upgrade replacement of traditional pressure gauge and traditionalpressure transmitter, is ideal pressure measuring instrument in industrial automatization. ceramic capacitance pressure transmitter is broadly used in liquid, gas, steam pressure measurement, liquidlevel measurement.特点● 精度高,稳定性好。● 二线制工作方式,4～20ma 信号输出。● 敏感部件及线路板采用全固体结构,坚固抗振。● 抗干扰能力强,温度稳定性好,防爆壳体结构,可全天候使用。● 具有最优良的防腐性能,保证最好的使用可靠性。● 结构轻巧,简单合理,无须支架,无须水平安装,可直接任意位置安装。characteristic● high accuracy, goodstability● 2 line working type, 4~20ma signal output● sensitive component and circuit board are in solid construction, rigid vibration-proof● excellent interference-proof, good thermal drift,explosion-proof enclosure structure, weather-proof● most outstanding corrosion-proof, ensure best utility reliability● light construction, simple reasonable, no bracket required, no horizontalmounting required, available mountingat anyposition.工作原理变送器由传感器与电子元件线路组成,被测介质的压力直接作用于传感器的陶瓷膜片上,使膜片产生与介质压力成正比的微小位移,正常工作状态下,膜片最大位移不大于0.025mm,电子线路检测这一位移量后,即把这一位移量转换成对应这一压力的标准工业测量信号即(4～20ma)。超压时膜片直接贴到坚固的陶瓷基体上,由于膜片与基体的间隙只有0.1mm,过载时膜片的最大位移只能是0.1mm,(此时测量膜片贴到陶瓷支架上,避免损坏)所以从结构上保证了膜片不会产生过大变形。由于膜片采用高性能的工业陶瓷,因而使传感器具有很强的抗冲击及抗过载能力。从衬底电极①和膜片电极②之间可以检测到与压力成比例的电容变化量,电容的变化值经激光微调电路放大输出高达0.5-4.5v的直流电压,计算机可直接采样。working principletransmitter is composed of sensor and electronic element circuit, pressure of measured medium directly applies on sensor s ceramic diaphragm, force diaphragm todisplace tinily in proportion to pressure of medium, under normal working condition, diaphragm displace no more than 0.025mm, electronic circuit detects this displacement, and convert it intostandard industrial measuring signal i.e. (4~20ma) corresponding to this pressure. when overpressure, diaphragm directly stick to solid ceramic base body, as there is only 0.1mm gap between diaphragmand base body, when overpressure, the maximum diaphragm displacement could be no more than 0.1mm, (at that time, measuring diaphragm sticks to ceramic bracket, avoid damage) so structurally preventdiaphragm from excessive deformation. because diaphragm adopts high functional industrial ceramic, sensor is significantly shock-proof and overload-proof. from between lining electrode① and diaphragmelectrode②capacitance variant in proportion to pressure can be detected, capacitance variant value is amplified by laser micro adjustment circuit to output direct voltage as high as 0.5-4.5v,computer can sample it directly.主要技术指标技术指标使用对象 液体、气体或蒸汽等测量范围 表压:0～1kpa～7mpa; 负压:-100kpa～7mpa输 出 4～20ma.dc电 源 13～30v.dc负载特性 4～20 ma.dc 二线制负载r ≤ 50(v-13)温度范围 环境温度:-20～+70℃;存储温度:-40～+85℃标准介质 温度:-30～+85℃(短时可达130℃)外壳防护 ip65防爆标志 本安型exia ⅱ ct5 ; 防爆合格证编号:ce042114main technical lndex technical indexutility object: liquid, gas or steam etcmeasuring range:gauge pressure: 0~1kpa~7mpa;minus pressure; -100kpa; 7mpaoutput: 4~20ma.dcpower supply: 13~30v.dcload characteristic: 4~20 ma.dc 2 line load ≤ 50(v-13)(see figure-2)temperature limit: ambienttemperature -20~+70℃ ;storage temperature -40~+85℃standard medium temperature: -30~+85℃short time up to 130℃enclosure protection: ip65explosion-proof mark: intrinsically safetytypeexiaiict5;explosion-proof certificate of conformity no.: ce042114 性能指标综合精度 提供标准±0.25%bfsl/年,最高精度± 0.1% bfsl/ 年稳 定 性 优于± 0.1% bfsl/ 年温度影响 在-20～+70℃范围内,变化量小于± 0.18%/10℃振动影响 在任何方向上振动频率为20-200hz时,变化量小于± 0.02%bfsl/ 年冲击影响 任何方向100g 冲击11ms 后,变化量小于± 0.02% bfsl负载影响 只要输入变送器的端子电压高于13v,就无负载影响。位置影响 无 结构指标结构材料 膜片材质:氧化铝陶瓷 外壳材质:铝合金石铸 接触介质材质:sus304“ o”型圈氟橡胶 (或聚四氟乙烯)过程连接 标准提供m20 × 1.5 阳螺纹电气连接可根据需要从任何一个出口引出,建议使用φ 10 工业电缆作为引线,以便密封。引出接头可选用通用电缆接头pg16或m20×1.5,不引线一端用端盖封住。functional indexgeneral accuracy: supply standard ± 0.25%bfsl/year,maximum accuracy ± 0.1%bfsl/yearstability: better than ± 0.1% bfsl/yearthermal effect: within-20～+70℃,variation below ±0.18%/10℃vibration effect: in any direction, vibration frequency20-200hz,variation below±0.02%bfsl/yearimpact effect: in any direction 100g impact after 11ms,variation below ± 0.02% bfslload effect: no load effect as long as voltage input to transmitter s terminal greater than13v.positioneffect: none constructional indexconstructional material: diaphragm material:aluminium oxide ceramicenclosure material:aluminium alloy stone castwetted material:sus304“ o”type ringfluoroelastomer (or ptfe)process connection: supply standard m20×1.5 male threadelectric connection:on request lead from any exit, suggest φ10 industrial cable as lead, so that it is sealed. leadoutsocketcould be general cable socket pg16 or m20×1.5,use end cap to seal no lead end. 结构及安装方式 ys1 压力变送器外型尺寸图figure-3 ys1 pressure transmitter external dimension drawing1. 直接安装在测量点上(任意角度)。2.尽量安装在温度梯度与温度波动小的测压点上,同时避免强振动和冲击。3. 室外安装时,尽可能放置于保护盒内,避免阳光直射和雨淋,以保持变送器性能稳定和延长使用寿命。4. 测量蒸汽或其它高温介质时,注意不要使变送器的工作温度超限。必要时请安装散热器或其它冷却装置连接。5.安装时应在变送器和介质之间加装压力截止阀,以便检修和防止取压口堵塞而影响测量精度。在压力波动范围大的场合还应加装阻尼器或压力缓冲装置。注:不得随意更换或改动可能影响防爆性能的元器件或结构。construction and mounting options1. directly mount on measuring point(any angle)2. suggest mount onmeasuring point with lower temperature gradient and temperature fluctuation, meanwhile avoid vibration and impact.3. in case of outdoor mounting, preferred mounting in protection case, avoid directexposure to sunlight and rainfall, to maintain transmitter s functional stability and longer service life.4. when measuring steam or other high temperature media, make sure transmitter s workingtemperature limit is observed. fit cooler or other cooling device if necessary.5. when mounting, shut valve should be used between transmitter and medium, for easy maintenance and to prevent pressuretaking port from blocking that influences measuring accuracy. damper or pressure buffer should be used where big pressure fluctuation exists.note:random replacing or alteringelements or construction that may impair explosion-proof function is prohibited.系统连接及调试变送器在测量系统中的连接见图4。建议电源电压vs 选用24v.dc。二次仪表中采样电阻(负载电阻)rl 的阻值选用250 ω。如果us 和rl 选用别的数值,那么rl =vs-12/0.02值不能超过由公式计算得到的数值。电源通过信号线接到变送器, 变送器顶部两侧面的连接孔用电缆密封或信号线装配,信号电缆通过紧固螺母锁紧,不使用的连接口必须密封。a:测量系统接线图在系统回路中必须采用屏蔽信号电缆,并可靠接地。s y s t e m -connection and adjustmentconnection of pressure transmitter inmeasuring system refers to figure 4. suggestpower supply vs uses 24v.dc。sampling resistance in secondary instrument(load resistance)rl uses 250 ω。ifresistance deviates for us and rl, rl value shallnot exceed the value from formularl= vs-12/0.02。power supply is connected to transmitter with signal cable, connections holes at both sides of top of transmitter is sealed with cable or assembledwith signal cable, signal cable is fastened by lock nuts, idle connection hole must be seaa:measuring system wiring schemeshielded signal cable must be used in system loop, and must be groundedfirmly.b:本安型压力变送器ys1本安型压力变送器采用本质安全电路,适用于爆炸危险区域,防爆等级exiaiict5(防爆合格证编号:ce042114),技术性能指标与普通型压力变送器相同。在系统回路中必须采用屏蔽信号电缆,并可靠接地。b:intrinsically safety type pressuretransmitterys1 intrinsically safety type pressure transmitter adopts intrinsically safety circuit, suitable for explosive hazardous zone, explosion-proof class exiaiict5(explosion-proofcertificate no.:ce042114),technical function index is same as standard pressure transmitter. shielded signal cable must be used in system loop, and must be grounded firmly.变送器出厂前已根据用户需求,量程、精度均已调到精度范围以内,一般不需校验。但以下情况需重新校验:a. 运输途中出现跌落、强烈震颠和碰撞；b. 存放期超过一年；c. 长时间运行后,出现大于精度范围内的误差；d. 使用单位的例行检验； before delivery transmitter has been set range, accuracy within accuracy range asper customer s request,normally doesn t need calibration but as a exception if following situations occur:a. falling down, strong shock and vibration in transit；b. over 1 year storage；c. long timeoperation, error occurs greater than accuracy range;d. user s routine inspection； 如何选择压力变送器(具体订货时参考)(1)确定测量介质根据腐蚀程度的大小选择相应的变送器,一般来说非强酸、强碱均可使用以不锈钢为隔离单元的变送器,否则只能选择专为防腐蚀设计的钛合金等特制变送器。其次还需看测量介质是否粘稠,干净程度,如果粘稠介质就需要选择硬性隔离单元的变送器。(2) 确定测量范围和测量方式一般选择测量范围时要考虑 实际测量范围,过压测量范围,选择量程以最大测量范围为准,同时考虑过压测量范围的大小。另外需要选择正确的测量方式,如果测量差压必须选择差压变送器。(3) 确定精度范围,补偿温度范围,使用温度范围根据需要测量的最低精度,一般选择略高于所要求最低精度的产品。 选择时还需考虑长期稳定性指标。 所谓补偿温度范围即正常工作时测量介质的温度范围,使用温度范围即使用过程中可能出现的最大温度范围,一般选择时略大于测量介质的温度范围。(4)确定供电电源、输出信号、压力螺纹接口、电气接口、机械尺寸等(5) 确定是否需要防爆,需要防电磁干扰,以及外壳防水的环境指标how to choose pressure transmitter(refer to when ordering)(1) decide measuring mediumchoose corresponding transmitter according tocorrosivity, normally transmitter with stainless steel isolation cell is enough for non strong acid strong alkali, otherwise special chemical seal product made in titanium alloy specially designedfor corrosion-proof must be used. secondly, need to know viscosity of measuring medium, cleanliness, in case of very viscous transmitter of rigid isolation cell needs to be used.(2) decide measuringrange and methodnormally when choosing measuring range, need to consider actual measuring range, overpressure measuring range, choosing range should refer to the biggest measuring range, meanwhileconsider volume of overpressure range. in addition, need to choose correct measuring method, if measuring pressure difference, need to use differential pressure transmitter(3) decide accuracy range,compensation temperature range, using temperature range.according to minimum accuracy, normally choose a bit higher accuracy meanwhile when choosing, need to consider long term stability compensationtemperature range is that measuring medium s temperature range when working normally, using temperature range is the biggest temperature range when using, normally choose a little bigger temperaturerange than required.(4) decide pressure connection, electric connection, mechanical dimensions etc(5) decide if need explosion-proof, electro magnetic interference-proof, and ambient factor ofwater-proof of enclosure 产品详细资料请点击:s.ys1 陶瓷电容压力变送.pdf压力变送器、防爆压力变送器陶瓷电容压力变送器ys-1、ys1

---

卓尔瑞华（北京）科技有限公司
何红梅
15910733293
北京市成寿寺路中街关家坑206号