dc电源插座主要适用于各种电子产品。例如：玩具，手机，笔记本电脑，数码产品，医疗设备，仪器仪表等。
郑生 dc电源插座中心针有:0.5mm/0.7mm/1.0mm/1.1mm/1.3mm/1.65mm/2.0mm/2.5mm/3.0mm
dc电源插座型号有：dc-001，dc-003，dc-001a，dc-003a，dc-002，dc-004，dc-002a，dc-005，dc-002c，dc-005a，dc-005b，dc-009，dc-005c，dc-009adc-006，dc-009c，dc-006a，dc-010，dc--006b,dc-011,dc-007,dc-011a,dc-011b,dc-013a,dc-012,dc-014a,dc-012a,dc-015,dc-012b,dc-015,dc-012b,dc-015a,dc-013,dc-015b,dc-015c,dc-020,dc-016,dc-021,dc-016a,dc-022,dc-017,dc-023,dc-018,dc-023a,dc-019,dc-023b,dc-024,dc-027,dc-025,dc-028,dc-025m,dc-028a,dc-025bm,dc-029,dc-026,dc-030,dc-026m,dc-030a,dc-031,dc-038,dc-031a,dc-038a,dc-033,dc-039a,dc-035-1,dc-040,dc-036,dc-041,dc-043,dc-048,dc-044,dc-049,dc-045,dc-049a,dc-046,dc-050,dc-074,dc-051,dc-047,dc-052,dc-053,dc-066,dc-055,dc-068,dc-056,dc-070,dc-060,dc-096手机专用尾插。
1.0构造tectonic
a型状、尺寸依照制品图而规定.
shape, size in accordance with the provisions of map products.
b外观:各部位应良好无秤锈、裂痕、电镀不良现象.
appearance : the good parts should weigh no rust, cracks, electroplating ill.
2.0 使用环境条件the use of environmental conditions
a环境湿度humidity: 25℃~+70℃
b 相对湿度relative humidity: ≤93% (+40℃)
c 机械性能mechanical properties
d 动作力power moves:3~25n
e 端子强度terminal strength
各端子在各方面承受500克力作用下,在10秒内,无脱落、破损等不良现象,但弯曲也可.
the terminals in all aspects under 500 caledon role, in 10 seconds, without any loss, damage and other negative phenomena, but also bending.
4.0 电气性能electrical performance
a 额定电流current ratings:dc 12v 1a.
b 接触电阻contact resistance:50mω以下.
c 绝缘电阻insulation resistance:
在端子之间各端子与壳之间加ac 500v 条件下,持续1分钟测试.100mω以上. the terminal between the terminal and shell in between 500v ac conditions, sustained a minute test ω m above .100.
d 抵抗电压resistance voltage:
在端子之间端子与壳之间加 ac 500v 60hz 条件下,持续1分钟测量.无击穿现象出现. in between the terminal and the terminal shell in between ac 500v 60hz conditions, sustained a minute measurement. no breakdown phenomenon.
5.0可靠性试验reliability test
a 寿命试验life test
以涂有薄层润滑脂的插头(涂润滑脂防止摩擦过热)以每分钟15~20次,无负载插座拨出5,000次，符合规格3.0和4.0规定值. coated with a thin layer of grease plugs (tu grease prevent friction overheated) per minute to 15 ~ 20, a no-load socket allocated5,000, with the specifications 3.0 and 4.0 provides value
b 温度试验temperature test
将插座放置于40±2℃,相对温度90%~95%环境中,96个小时后取出,取去水滴,将插座放置于常温常湿环境中,于30分钟内测试,符合规格3.0和4.0要求. socket to be placed on the 40 ± 2℃, relative humidity of 90% ~ 95% of the environment, 96 hours after the removal,taking a drop of water, will be placed in the socket temperature often wet environment, in the test within 30 minutes, with 3.0 and 4.0 specifications required.

---

东莞市长安奋展电子开关经营部
郑建忠
13925753768
东莞市桥头镇高新开发区