beeprog+通用型编程器
■来自欧州的第一品牌编程器■支持 48 pin 万用驱动 , 软件免费更新下载■三年质量保证，无后顾之忧 ■体积小巧，功能强，携带方便 ■pin 脚自动检测，提供实时侦测信息 ■支持 in-circuit programming(isp)■通过 usbhub可并连多台机器量产烧录■提供详尽的实时帮助文档和相关的ic资料 ■可测试 ttl/cmos 的逻辑 ic和memories
概要
◆elnec基于windows95/98/me/nt/2000/xp 界面的新的兼容usb的通用烧录器首要成员,能很好地满足发展的社会对于快速和可靠性通用编程器的要求.
◆在没有一系列具体module的情况下,能支持各种类型、当今的和未来的可烧写设备的硅技术.为设备能自由选择最佳设计.通过使用isp连接器,在电路板上,编程器能烧写支持 isp 芯片.
◆beeprog不仅是一个烧写器,而且还能测试ttl/coms 逻辑 ic和内存.此外,它允许使用者使用一系列的测试方式 .
◆提供非常有竞争力的价格,为可靠烧写外加卓越的硬件设计,在这方面是性价比最好的烧写器.由于高速fpga硬件驱动和烧写器内部时序程序运行,有着非常快的烧写速度.从这点上说至少比同类竞争品要快,对于许多芯片的烧写速度,也要比同类竞争品要快.因此,在烧录座上当要生产时,只要等待操作 , 而不像其它的完整操作方式.
◆beeprog通过usb(2.0/1.1)口或者任何标准并行（打印机）口就能连接 ibm 486 以上的 pc、手提式的、个人桌面电脑.编程器也支持ieee1284(ecp/epp) 高速并口。支持选择的 usb/lpt 口连 beeprog到任一pc,包括从最近的笔记本电脑到没有 usb 口的旧的桌面型电脑
.
硬件
◆fpga基于 48 个强有力的ttlpin 驱动,为每一个测试座上的 pin 脚提供high/low/pullup/pulldown/read功能.先进的驱动技术结合高速高质线路的可靠性能.最低支持电压低至1.8v,因此您可以用它烧录当前世界上所有流行的低压器件.
◆烧录器提供插入测试和接触测试在进行烧录之前,并可以防止因放置不当接触不好造成的芯片损坏.这些性能通过过流保护和流量检查因误操作阻止芯片损坏.
◆内嵌的保护电路能消除烧写器的损坏或因环境或误操作损坏烧写器.beeprog烧写器的所有输入,包括zif 测试座,连接到 pc 机的先进的驱动技术提供高速高质的可靠性能.最低支持电压低至1.8v,因此您可以用它烧录当前世界上所有流行的低压器件.
◆烧录器提供接触测试在进行烧录之前,并可以防止因放置不当造成的芯片损坏.这些通过过流保护和流量检测阻止因误操作损坏芯片.
◆内嵌的保护电路能消除烧写器的损害或者因环境或误操作的烧录器的损害.beeprog烧录器的所有输入,包括zif 测试座、连接 pc 的、供电,都被保护 , 防止 ecd 上升到15kv.beeprog烧录器执行边沿级别的电压烧录校验,这样能明显的提供烧录领域,保持长数据.
◆各种各样的适配器支持各种 ic封装,例如 :plcc, soic,psop,ssop, ssop,tsoptsslp,tqfp,qfn(mlf)sdip,bga等.
软体
◆这款烧录器容易使用并进行控制,具备下拉菜单,快捷键和在线帮助.选择器件可以通过选择分类,制造厂商,型号,序列号等多种方法进行.
◆相关的标准烧录操作命令(read, blank check, program,verify,erase),还有一些测试功能(插入测试,流量检测),也包括一些额外的功能如(autoincrement,product 模式 -在插入芯片以后立刻开始烧).
◆支持所有已知的数据格式,当导入文件时能自动识别并转换合适的文件格式.
◆自动递增烧录功能可以在每一颗 ic中分配不同的序列号 , 也可以简单的递增序列号 ,也可以选择从用户自己的文件读取序列号.烧录器软体提供详尽的 ic讯息包括画的各种有用的封装,芯片标签的说明(前缀和后缀的意思).
◆烧录器软体提供详尽的 isp讯息,包括为当前所选 ic 的 isp 接口定义,ic周边电路建议设计,以及其它必要讯息.通过其它应用命令使用 bat 或 dll文件 , 远程控制允许 pg4uw软体流控制.jedec 标准的 jesd-71 中的 jam 文件通过 jamplayer说明,通过各自烧写器的厂商提供的设计软件产生 jam 文件.芯片在 zif 座或 isp 连接器 (ieee1149.1jtag接口)烧录.
◆vme文件通过 vmeplayer说明.vme 文件是一个关于 svf 文件压缩的二进制变异,包含高层 ieee1149.1总线实施.通过各自烧写器的厂商提供的设计软件产生 vme 文件.芯片在 zif 座或 isp 连接器(ieee1149.1jtag接口)烧录.通过 jtag 链 (isp-jam 或isp-vme)多个设备有可能烧写和检测.
◆一个强有力的多烧写程序能实现在同一台pc(通过usb口)上连接多个beeprog烧写器,支持许多芯片,正如单一 beeprog 烧录器所支持的,同时也不会明显的降低烧录速度.众所周知,协作的多烧录-每一烧录器能独立工作,每一烧录器也能烧录不同的芯片.
· care forthecustomers
·itis important to remember, that a support of most of the newdevicesrequiresonly asoftwareupdate, becausethebeeprog is truly a universal programmer. with our promptserviceyou can have new device added to the list of supporteddeviceswithin hours! see algor (algorithm on request)servicefor details.
·freesoftwareupdatesare availablebydownload from ourwebsite.
·keep-current and algor services, our nextsteptowards customer satisfaction.
keep-currentservice means, that elnec ships the latestversionof programmer software and updated user documentation(keep-currentpackage) to customer . the keep-current service isyour hassle-freeguarantee that you achieving the highest qualityprogramming onelnec programmers, at minimalcost.algor(algorithm on request) service gives the useratool to influence amount and types of programmed devicesasneeded.·advanced design of the beeprog programmer,including protectivecircuits, original brand components, andcareful manufacturing andburning allows us to provideathree-yearwarrantyonparts andlabor for the programmer (limited 25 000-cycle warranty onzifsockets).
specificationhardwarebaseunit,dacs
·usb2.0 port
·fpgabased ieee 1284 slave printer port, up to 1mb/stransferrate
·on-board intelligence: powerful microprocessorand fpga based statemachine
·three d/a converters for vccp, vpp1, and vpp2,controllable riseand fall time
·vccprange 0..8v/1a
·vpp1, vpp2 range 0..26v/1a
·autocalibration
·selftest capability
·protection against surge and esd on power supplyinput, parallelport connection
zifsocket, pindriver
·48-pin dil zif (zero insertion force) socketaccepts both 300/600mil devices up to 48-pin
·pindrivers: 48 universal
·vccp/vpp1/vpp2 can be connected to eachpin
·perfect ground for each pin
·fpgabased ttl driver provides h, l, clk, pull-up, pull-down onallpindriver pins
·analog pindriver output level selectable from 1.8v up to26v
·current limitation, overcurrent shutdown, powerfailureshutdown
·esdprotection on each pin of socket (iec1000-4-2: 15kv air,8kvcontact)
·continuity test: each pin is tested before everyprogrammingoperation
ispconnector
10-pin male typewithmissinsertion lock5ttlpindrivers, provides h, l, clk, pull-up, pull-down; levelhselectable from 1.8v up to 5v to handle all (low-voltageincluding)devices.1xvccp voltage (range2v..7v/100ma), can be applied to pins 1,3programmed chip voltage(vccp)with both source/sink capability and voltagesense1x vpp voltage(range2v..25v/50ma), can be applied topins2,3,4,6,8,10target system supplyvoltage(range 2v..6v/250ma)device supportprogrammer, inzifsocket
·eprom: nmos/cmos, 2708*, 27xxx and 27cxxx series,with 8/16 bitdata width, full support for lvseries
·eeprom: nmos/cmos, 28xxx, 28cxxx, 27eexxx series,with 8/16 bitdata width
·flash eprom: 28fxxx, 29cxxx, 29fxxx, 29bvxxx,29lvxxx, 29wxxx,49fxxx series, from 256kbit to 32mbit, with 8/16bit data width,full support for lv series
·serial e(e)prom: 24cxxx, 24fxxx, 25cxxx, 45dxxx,59cxxx, 25fxxx,25pxxx, 85xxx, 93cxxx, nvm3060, mdaxxx series, fullsupport for lvseries
·configuration (ee)prom: xcfxxx, xc17xxxx,xc18vxxx, epcxxx,at17xxx, 37lvxx
·1-wire e(e)prom: ds1xxx, ds2xxx
·prom: amd, harris, national, philips/signetics,tesla,ti
·nvram: dallas dsxxx, sgs/inmos mkxxx, simtek stkxxx, xicor 2xxx,zmdu63x series
·pld:altera: max 3000a, max 7000a, max 7000b, max7000s,max7000ae
·pld:lattice: ispgal22v10x, isplsi1xxx, isplsi1xxxea,isplsi2xxx,isplsi2xxxa, isplsi2xxxe, isplsi2xxxv, isplsi2xxxve,isplsi2xxxvl,lc4xxxb/c/v/zc, m4-xx/xx, m4a3-xx/xx,m4a5-xx/xx,m4lv-xx/xx
·pld:xilinx: xc9500, xc9500xl, xc9500xv, coolrunnerxpla3,coolrunner-ii
·other pld: spld/cpld series: ami, atmel,amd-vantis, gould,cypress, ict, lattice, ns, philips, stm, vlsi,ti
·microcontrollers 48 series: 87x41, 87x42, 87x48,87x49, 87x50series
·microcontrollers 51 series: 87xx, 87cxxx, 87lvxx,89cxxx, 89sxxx,89lvxxx, all manufacturers, philips lpcseries
·microcontrollers intel 196 series:87c196kb/kc/kd/kt/kr/...
·microcontrollers atmel avr: at90sxxxx, attiny,atmegaseries
·microcontrollers cypress:cy8cxxxxx
·microcontrollers elan: em78pxxx
·microcontrollers microchip picmicro: pic10xxx,pic12xxx, pic16xxx,pic17cxxx, pic18xxx, dspicseries
·microcontrollers motorola: 68hc05, 68hc08,68hc11series
·microcontrollers national: cop8xxxseries
·microcontrollers nec: upd78pxxxseries
·microcontrollers scenix (ubicom): sxxxxseries
·microcontrollers sgs-thomson: st6xx, st7xx,st10xxseries
·microcontrollers ti: msp430 and msc121xseries
·microcontrollers zilog: z86/z89xxx andz8xxxseries
·microcontrollers other: em microelectronic,fujitsu, goalsemiconductor, hitachi, holtek, princeton, macronix,winbond,infineon(siemens), nec, samsung, toshiba,...
programmer, through ispconnector
·serial e(e)prom: iic series
·microcontrollers atmel: at89sxxx, at90sxxxx,attiny, atmegaseries
·microcontrollers cypress:cy8c2xxxx
·microcontrollers elan: em78pxxx
·microcontrollers em microelectronic: 4 and 8bitseries
·microcontrollers microchip picmicro: pic10xxx,pic12xxx, pic16xxx,pic17xxx, pic18xxx, dspicseries
·microcontrollers motorola/freescale: hc08 gt, lj,qy, qtseries
·microcontrollers philips: lpcseries
·microcontrollers ti: msp430
·pld:lattice: ispgal22xv10x, isplsi1xxxea, isplsi2xxxe,isplsi2xxxv,isplsi2xxxve, isplsi2xxxvl, m4-xx/xx, m4lv-xx/xx,m4a3-xx/xx,m4a5-xx/xx, lc4xxxb/c/v/zc
·various pld (also by jam player/jtag support):altera: max 3000a,max 7000a, max 7000b, max 7000s, max 9000, max iixilinx: xc9500,xc9500xl, xc9500xv, coolrunnerxpla3,coolrunner-ii
notes:
devices marked * are obsolete,programmingwithadditionalmodulefor all supported devicesseeactualdevicelisti.c. tester
·ttltype: 54,74 s/ls/als/h/hc/hct series
·cmostype: 4000, 4500 series
·static ram: 6116 .. 624000
·userdefinable test pattern generation
package support
·package support includes dip, plcc, soic, psop,ssop, tsop, tssop,tqfp, qfn (mlf), sdip, bga andother
·support all devices in dip with defaultsocket
·support devices in non-dip packages up to 48 pinswith universaladapters
·programmer is compatible with third-partyadapters for non-dipsupport
programmingspeednotes:·itis important to know, we always use random numbers patternforprogramming speed testing. some our competitors usesparsepattern, where only few non-blak data are programmed or arethereare used data with only few 0 bits (fe, ef, etc.). thischeatingapproach can decrease programming time considerable. ifyou planto compare, ask always which pattern theyuse.
·the programming speed depends on pc speedonlyslightly.
.gif.gif

---

昆山市德正微电子有限公司
黄普勇
13584823195
昆山市花桥镇赛格电子市场2E26柜台